ACT Cable de instalación azul S/FTP CAT6A B2ca PoE++ 100W de 30 metros, conductor macizo, preensamblado, conector RJ45 macho – macho

The ACT S/FTP CAT6A B2ca PoE++ 100W prefab installation cable 30m (FB0030) is a pre-terminated, solid conductor network cable designed for fixed installations that require 10 Gigabit Ethernet performance and up to 100 W Power over Ethernet (4PPoE / PoE++). This 30 meter blue installation cable uses individually foil-shielded pairs with an overall braid (S/FTP) to reduce electromagnetic interference, and features 23 AWG full copper conductors and 50 µ gold-plated RJ45 contacts fitted with IDC termination for reliable long-term connections. The cable meets ANSI/TIA-568.2-D and ISO/IEC 11801-1 standards and carries a CPR Euroclass B2ca rating for use in high-risk environments.

Advantages

Pre-terminated RJ45 male-to-male connectors eliminate field termination and reduce installation time and risk of wiring errors. The S/FTP construction with foil-shielded pairs and braid improves immunity to crosstalk and external interference, supporting stable 10 Gigabit data transmission. IDC contacts and 23 AWG solid copper conductors are suitable for sustained 100 W PoE++ (type 4) applications. The Euroclass B2ca fire performance allows use in demanding commercial, institutional, and data centre environments while complying with applicable CPR requirements.

Suitable for

• High-speed 10 Gigabit Ethernet backbone and horizontal runs in offices and data centres
• Power over Ethernet installations requiring up to 100 W (4PPoE / PoE++), including powered switches and cameras
• Fixed in-wall, floor-duct, or cabinet installations where pre-terminated solid cables speed deployment
• Environments with elevated fire-safety requirements such as commercial buildings, healthcare and education facilities

When it may not be suitable

This prefab solid installation cable is intended for fixed installations and is not designed for frequent flexing or use as a patch cable in high-movement areas; repeated bending may damage the solid conductors or connectors. It is also not intended for field termination—if bespoke connector types or custom lengths shorter than the prefab length are required, a different product or on-site termination will be necessary.

Key specifications

• Cable length: 30 m
• Conductor: solid copper, 23 AWG
• Shielding: S/FTP (foil around each pair + overall braid)
• Connector type: RJ45 male – RJ45 male, 50 µ gold-plated contacts, IDC termination
• Performance class: Category 6A, suitable for 10 Gigabit Ethernet
• Power support: 4PPoE / PoE++ up to 100 W (type 4)
• Fire performance: CPR Euroclass B2ca
• Standards compliance: ANSI/TIA-568.2-D and ISO/IEC 11801-1
• Colour: Blue

How to use

Route the pre-terminated cable through ducts, conduit, or behind walls as required for the installation. Secure the cable according to local regulations and building codes, avoiding sharp bends and excessive pulling tension. Insert the RJ45 male connectors into compatible network ports or patch panels; the cable is plug-and-play and requires no additional termination or special tools. For PoE++ applications, ensure connected equipment supports 4PPoE and verify power budgets to confirm safe operation at up to 100 W.

What to consider before purchase

• Intended use: suitable for fixed in-wall or cabinet installations, not for frequent flexing or use as a portable patch cable
• Length: confirm 30 m meets the planned run and cable route without excess bending or strain
• Power requirements: verify that connected devices and switches support 4PPoE / PoE++ 100 W if using PoE power delivery
• Fire and building codes: ensure Euroclass B2ca meets local installation regulations and site requirements

Recommendations

Avoid tight bends (maintain manufacturer minimum bend radius), do not exceed recommended pull tensions during installation, and test each link after installation for continuity, performance and PoE delivery. Use this pre-terminated S/FTP CAT6A cable for fixed, permanent runs where high data rates, shielding and certified fire performance are required.