DRYFLUID Gear Lube slide lubricant (10 ml)

DryFluid Extreme Gear Lube is a high-end dry slide lubricant specially developed for highly stressed gears in modelling applications, including model helicopters, RC cars, trucks, model railways, and servos, as well as axles, joints, and bearing systems.

Utilizing dry particles, sliding polymers, and sliding fluids instead of classic grease or oil, this silicone-free, non-greasy formula dries into a white, pressure-resistant, and highly adhesive lubricant film.

It reduces power loss through friction, running noise, and wear while offering extreme material compatibility and minimal dust and dirt adhesion.

The 10 ml bottle includes a pinpoint dispenser, a separate fine cannula for precise application, and a fine hair paintbrush for surface applications.

• Dry lubricant for highly stressed gears in modelling applications

DryFluid Gear Lube is a dry lubricant developed for highly stressed gears in modelling applications. It has low sliding friction, pressure resistance and adhesion, with minimal dust and dirt adhesion.

It is used on gears of model helicopters, RC cars, trucks, model railways and servos, and can also be applied to axles, joints and bearing systems in modelling applications.

It is not a classic grease or wax, is neither greasy nor oily, and is silicone-free. Its multistage lubricant system uses dry particles, sliding polymers and sliding fluids for a long-lasting lubricating effect. After application, the fluid dries to form a white lubricant film.

• Highlights
• Pressure resistance, long-term stability and adhesion
• Compatible with current metal, plastic and natural rubber materials
• Repels dust and dirt
• Specifications
• Content: 10 ml
• In the box
• 1× pinpoint dispenser
• 1× separate fine cannula
• 1× fine hair paintbrush

The pinpoint dispenser and fine cannula allow precise application; the fine hair paintbrush is for surface applications.

DryFluid Gear Lube is a slide fluid for highly stressed gears in modelling. It is suitable for gears of model helicopters, RC cars, trucks, model railways and servos as well as shafts and cardan systems. Solid lubricant components ensure a low tendency to bind dust and dirt.

The slide fluid is not a grease, does not oil and is silicone-free. It contains dry particles, sliding polymers and adhesive sliding fluids and is designed as a multi-stage lubricant system for long-term effect.

• Reduces power losses due to friction and running noise
• Reduces wear
• Pressure-resistant and long-term stable, with high adhesion
• Material compatible with metals, plastics and rubber materials
• Technical data
• Product name: DryFluid Gear Lube
• Colour
• Liquid state: whitish transparent
• Resting state: White
• Density
• In liquid state: 0.91 g/cm³
• In dry state: 1.18 g/cm³
• Boiling point liquid: 82 °C
• Viscosity
• In liquid state (20 °C): Not determined
• In dry state: Not determined
• Temperature range
• Temperature resistance: −50–160 °C
• Recommended temperature range: −20–120 °C
• Specific electrical resistance
• Component microceramics: 10 E+12 Ohm × cm
• Component plastic sliding polymer: 10 E+16 Ohm × cm
• Component sliding fluid: 2.0 × 10 E+3 Ohm × cm
• Total conductivity: > 2.0 × 10 E+3 Ohm × cm
• Lubricant properties
• Pressure resistance according to DIN 51347: 185 N/mm²
• Friction coefficient: 0.13
• Content: 10 ml
• Scope of delivery
• 1× dosing tip
• 1× dosing cannula
• 1× fine hair paintbrush
• Notes
• Apply a thin layer of Gear Lube sparingly; shake well before use.

If possible, apply to a vertically standing gear and rotate it while doing so.

For hard-to-reach places and spot applications, use the enclosed cannula; for a fine, even distribution, spread the Gear Lube with the fine hair paintbrush immediately after application.

Gears that have not been treated with Gear Lube before should be thoroughly cleaned before use.

The specific electrical resistance was measured in the dry state according to DIN EN 50359.

• Brand: DryFluid