Cuenta Contacto
Tu carrito
Envío con DPD y FedEx
¿Dudas? Pregunte a la IA

Espada para motosierra Einhell 4500151

Espada para motosierra Einhell 4500151
Espada para motosierra Einhell 4500151
Espada para motosierra Einhell 4500151
Espada para motosierra Einhell 4500151
Espada para motosierra Einhell 4500151
Espada para motosierra Einhell 4500151
29,80 €
PDF
PDF
Stock 1 Código 348509 Modelo 4500151 Garantía 3 años

Envíos y devoluciones

Entrega estimada martes, 8 de diciembre
Te mantendremos informado a través de nuestro sistema de seguimiento detallado
Opciones de pago
Tarjeta bancariaVisaMastercardPayPalApple PayGoogle PayTransferencia bancaria

Haz una pregunta: el asistente IA responde al instante.

Descripción

The Einhell 4500151 chainsaw bar is a replacement guide bar designed for compatibility with Einhell BG-PC 3735. With a length of 45 cm, the bar provides a stable, straight guide for the saw chain to ensure accurate cutting through logs and timber. Manufactured for durability, the bar is intended to withstand the mechanical stresses of routine cutting tasks while promoting smooth chain movement and reduced vibration during operation.

Advantages

The 45 cm length balances cutting capacity and maneuverability, allowing deeper cuts while remaining manageable for general-purpose work. The bar is made from treated steel to resist wear and maintain alignment under load, which supports consistent cutting performance. Its profile is engineered to promote efficient oil distribution along the chain, contributing to lower friction and extended chain life. Designed to fit specified Einhell models, the bar simplifies maintenance by matching mounting points and guide requirements.

Suitable for

  • Replacing a worn or damaged guide bar on compatible Einhell chainsaws
  • Cutting firewood, small to medium logs and general timber preparation
  • Home workshop and light professional outdoor work where a 45 cm bar is appropriate

Key specifications

  • Bar length: 45 cm
  • Compatibility: designed to fit Einhell BG-PC 3735 and equivalent guide specifications
  • Material: hardened/treated steel guide construction for wear resistance
  • Profile: standard guide profile with oil grooves for chain lubrication

How to use

Before installation, ensure the saw is switched off and the spark plug or power source is disconnected to prevent accidental start. Remove the chain and the old bar according to the saw manufacturer’s instructions, then position the new bar on the mounting studs and refit the chain, making sure chain tension and alignment meet the recommended specifications. After installation, check chain tension after a short trial run and adjust lubrication flow as needed to ensure proper oiling of the bar and chain.

Recommendations

Use bar-specific chain sizes and maintain proper lubrication to extend service life. Regularly inspect the bar rails for wear and the oil groove for clogging. Replace the bar if bending, excessive wear or groove damage is detected. Follow the chainsaw manufacturer’s maintenance schedule and safety instructions when performing replacements or adjustments.

Aspectos destacados
  • Replacing a worn or damaged guide bar on compatible Einhell chainsaws
  • Cutting firewood, small to medium logs and general timber preparation
  • Home workshop and light professional outdoor work where a 45 cm bar is appropriate
  • Bar length: 45 cm
  • Compatibility: designed to fit Einhell BG-PC 3735 and equivalent guide specifications
  • Material: hardened/treated steel guide construction for wear resistance
  • Profile: standard guide profile with oil grooves for chain lubrication
Historial de precios de los últimos 6 meses
Espada para motosierra Einhell 4500151
Actual
29,80 €
Mínimo 7 d
29,42 €
Máximo 7 d
29,80 €
Variación 24 h
0,00 €   0%
Variación 7 d
+0,38 €   +1%
Variación 30 d
0,00 €   0%

Escribir una opinión

Valoración *
Tu nombre se mostrará públicamente: puedes usar un apodo. Invitamos a los compradores a escribir opiniones; las revisamos antes de publicarlas y publicamos también las críticas.
Vendedor: UAB KUR LT · Gariūnų g. 57-14, LT-02300 Vilna, Lituania · Código de empresa 303192950 · NIF-IVA UE LT100008198612 · Envío desde la UE (Lituania)
WhatsApp
Messenger
Hola, soy el asistente de IA de DistriNode. Puedo ayudarte a encontrar productos, comparar opciones, crear presupuestos en PDF o abrir solicitudes de soporte.
Todas las categorías