Pintura en espray GHIANT Lexan roja n.º 110 150 ml

This ready-to-use, quick-drying, and fuel-resistant red paint in a 150ml spray can is specially developed for painting polycarbonate RC car bodies.

The special solvent etches the surface to allow the paint to bond permanently, resulting in a lightweight finish that can save up to 15g of weight on a 1/10 scale race body compared to pre-painted or water-based alternatives, which helps achieve a lower center of gravity.

For best results, the paint is applied in multiple light coats from a distance of approximately 20 to 30 cm with about 5 minutes of drying time between layers.

• Red spray paint for polycarbonate RC car bodies, 150 ml
• Specifications
• Hazard statements (H codes)
• H222: Extremely flammable aerosol.
• H229: Pressurized container: may burst if heated.
• H319: Causes serious eye irritation.
• H336: May cause drowsiness or dizziness.
• Precautionary statements (P codes)
• P210: Keep away from heat, hot surface, sparks, open flames and other ignition sources. No smoking.
• P251: Do not pierce or burn, even after use.
• P305 / P351 / P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P337 / P313: IF eye irritation persists: Get medical advice/attention.
• P403 / P233: Store in a well-ventilated place. Keep container tightly closed.
• P410 / P412: Protect from sunlight. Do not expose to temperatures exceeding 50 °C/122 °F.
• Supplemental hazard information
• EUH066: Repeated exposure may cause skin dryness or cracking.
• In the box
• 1× 150 ml spray paint

Before painting, remove dirt particles, cut out the body and sand the cut edges. Mask areas that are not to be painted with masking film or tape; make sure surfaces are dry and free of dust.

Many bodies have a transparent protective foil on the outside. Do not remove it until the paint has dried.

Paint dark colours before light colours to prevent the dark colours from showing through.

Shake the can vigorously for approx. 2 min. before use, until the mixing ball rattles. Spray from approx. 20–30 cm using even cross movements.

Covering capacity varies slightly by colour. Apply light coats to avoid bleeding; the final result takes 2–3 coats. Wait approx. 5 min. between coats rather than applying one heavy coat. Let the paint dry for 5 minutes before removing the masking film and applying the next coat.

After use, turn the can upside down and spray for 2 s until the nozzle is empty.

For fluorescent colours, apply only very light coats at temperatures above 15 °C, spraying from a distance of +/-15/20 cm. Fluorescent colours appear to cover less well than normal colours.

Let fluorescent colour dry for 30 min., then back it with white RC Car Colour to obtain the fluorescent effect.

The paint remains elastic, even in a strong crash, and does not splinter or scratch.

• Highlights
• Remains elastic
• Bonds permanently to the body
• Fuel-resistant
• Technical data
• Hazard statements (H codes)
• H222: Extremely flammable aerosol.
• H229: Pressurized container: may burst if heated.
• H319: Causes serious eye irritation.
• H336: May cause drowsiness or dizziness.
• Precautionary statements (P codes)
• P210: Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
• P251: Do not pierce or burn, even after use.
• P305 / P351 / P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P337 / P313: If eye irritation persists: Get medical advice/attention.
• P403 / P233: Store in a well-ventilated place. Keep container tightly closed.
• P410 / P412: Protect from sunlight. Do not expose to temperatures exceeding 50 °C/122 °F.
• Supplemental hazard information
• EUH066: Repeated exposure may cause skin dryness or cracking.
• In the box
• 1× Lexan paint red no. 110, 150 ml
• Notes

If there is a protective foil on the outside of the body, remove it only after painting; the body can be cut out beforehand.

Clean the body thoroughly with dish soap or brake cleaner and shake the can vigorously for about 2 minutes.

Spray the paint from a distance of 20–30 cm. When using multiple colours, start with the darkest, as dark colours can otherwise show through light ones.

Apply several thin coats instead of one thick coat and wait about 5 minutes between sprays.

Wait at least 5 minutes before removing the protective film or masking film of the design.

After use, turn the can upside down and spray for about 2 seconds to empty the nozzle.

• Brand: Ghiant