Switch Cudy GS1016E 16 puertos Gigabit Ethernet switch no gestionado, 16× 10/100/1000 Mbit/s

Description: 16-Port Gigabit Light Managed Switch 802.1Q / MTU / Port-Based / Voice VLAN 802.1Q VLANs allow you to create secure and efficient network segments across multiple managed switches. MTU- and port-based VLANs provide a simpler way to configure local VLAN networks. QoS DSCP / 802.1p / Port-Based DSCP/802.1p QoS identifies DSCP packets in traffic and prioritizes latency-sensitive data. Link Aggregation Enables the creation of multiple LAG groups to increase backbone bandwidth. DHCP Snooping Assign an authorized DHCP server to prevent network downtime caused by unauthorized DHCP servers connecting to the network. IGMP Snooping Identifies multicast groups connected to the switch and forwards data only to the appropriate ports instead of broadcasting it. Loop Prevention STP/RSTP improve network performance and automatically eliminate loops with other managed switches. A basic loop prevention function is activated when STP/RSTP is disabled. Basic VLAN Mode Disables management features and prevents communication between downlink ports, enhancing network security. Extended Mode Disables management features and extends transmission distance up to 250 meters, simplifying installation. Port speed in this mode is limited to 10 Mb/s. | Switch class: Managed | Application: Home and small office | Switch layer: L2 | Network architecture: GigabitEthernet | Number of 10/100 Mbps ports: None | Number of 10/100/1000 Mbps ports: 16 | 10/100/1000/2500 Mbps ports: None | Number of 10Gb ports: None | Number of ports 25Gb: None | Number of PoE ports (PoE & PoE+): None | Number of PoE+ ports: None | Number of COMBO ports: None | Number of SFP ports: None | Number of SFP+ ports: None | Number of SFP56 ports: None | Number of QSFP+ ports: None | Console port: No | Throughput: 32 | Forwarding rate: 23.808 | Memory buffer: 4 | MAC address table size: 8192 | Support for Jumbo frames: Yes | Jumbo frame size: 15 | Supported protocols and standards: 802.3x Flow Control 802.3i 10BASE-T 802.3u 100BASE-TX 802.3ab 1000BASE-T 802.3az Power Saving 802.1d: STP 802.1w: RSTP 802.1p: LAN Layer 2 QoS/CoS 802.1q: VLAN Bridge Operation 802.1ab: LLDP/LLDP-MED | L2 features: IGMP Snooping Loop Prevention DHCP Snooping STP/RSTP LLDP Config and Neighbors MTU VLAN Port-Based VLAN 802.1Q VLAN Voice VLAN DSCP QoS 802.1p QoS Port-Based QoS | Chassis type: Rack | Power consumption: 7.8 | Environment requirements: Operating temperature: 0°C to 40°C Storage temperature: -40°C to 70°C Operating humidity: 10% to 90%, non-condensing Storage humidity: 5% to 90%, non-condensing | Accessories included: GS1016E Power cord Installation guide Mounting kit | Power supply: Power supply methods: AC AC input: 90-260 V~, 50/60 Hz Maximum power consumption: 7.8 W Idle power consumption: 4.5 W | Dimensions: 200 × 118 × 44 mm | Weight: 625.5 | Data Act: Link

How to use

Place the switch on a stable surface or mount it according to available mounting options. Connect the switch to your router or modem using an Ethernet cable to the uplink port, then connect devices such as PCs, NAS units, media players, or NVRs to the remaining RJ45 ports. Ensure the power adapter is connected to a suitable AC outlet; the unit will power on and negotiate link speeds automatically. No software installation or management interface is required.

Recommendations

For best performance, use quality Cat5e or Cat6 Ethernet cables and connect bandwidth‑sensitive devices directly to the Gigabit ports. Place the switch in a well‑ventilated area to maintain optimal operating temperature and avoid exposure to moisture or excessive dust. When integrating with camera systems, verify that connected devices do not require Power over Ethernet (PoE) or use a separate PoE injector if needed.