Batería LiFePO4 Pylontech 2x US3000D 48 V, paquete de almacenamiento de 7 kWh, con soportes y cable de conexión

The Pylontech US3000D lithium iron phosphate battery is a high-quality energy storage for integration into PV systems with an increased depth of discharge of 95%.

• Nominal voltage 48V, nominal capacity 3.55 kWh per storage module.
• With matching brackets.
• Including inverter connection set.

In this bundle from Offgridtec (MPN 016085), in addition to the Pylontech US3000D LiFePO4 battery, matching brackets are provided, which are useful for better air circulation and vertical stacking of the batteries. You also receive an inverter connection set for connecting all components.

The Pylontech US3000D set contains

• 2x Pylontech US3000D 48 V LiFePO4 battery module with 3.55 kWh

2x Pylontech bracket / brackets for US3000C and US3000D LiFePO4 battery

• 1x Pylontech battery connection cable set Pylontech to inverter
• The US3000D from Pylontech is a low-voltage battery module with LiFePO4 technology. The modular energy storage has a nominal capacity of 3.55 kWh and a nominal voltage of 48 V. The battery is designed for stationary energy storage systems and can be expanded in parallel within a battery group with up to 16 modules. An integrated battery management system (BMS), CAN and RS485 communication as well as the compact design for 19-inch rack systems support integration into scalable storage solutions.
• Scalable 48 V battery storage with integrated BMS
• 3.55 kWh nominal capacity and 3.3 kWh usable capacity
• 48 V nominal voltage for low-voltage storage systems
• Lithium iron phosphate technology (LiFePO4)
• 95% depth of discharge (DoD)
• Soft start to limit inrush current
• Expandable up to 16 battery modules per battery group

Integrated battery management system (BMS) for monitoring and protecting the storage

CAN and RS485 interfaces for communication with compatible system components

• More than 8,000 cycles at 25 °C
• Natural cooling without active fans
• Status and state of charge display via LEDs
• Modular design for different storage capacities

Individual modules can be connected in parallel, allowing the storage capacity to be adapted to the respective energy demand. Within a battery group, up to 16 modules are possible. For larger systems, multi-group operation is also possible. Parallel connection is particularly relevant when an existing storage system is to be expanded later. A new battery module can be added to an existing system without problems. Before expansion, however, the states of charge of the batteries must be equalized. Important note: The previous version US3000C can also be combined. The newest battery must always be set as master.

• Integrated BMS for monitoring and protection

A battery management system is integrated in the battery. The BMS monitors important operating states and takes over protective functions for charge and discharge voltage, charge and discharge overcurrent, high or low cell temperatures as well as short circuit. In addition, the calculation of the available capacity, the monitoring of the circuit and the communication with the inverter are among the described functions. The LEDs on the front allow operating status, alarm states and the current state of charge (SOC, State of Charge) to be recognized directly on the battery module.

• Pylontech Brackets

The Pylontech brackets are used for vertical stacking of the Pylon battery modules US3000D. The batteries should not be stacked directly on top of each other without spacing. Via a clamping device on the sides of the bracket, stacked brackets can be connected and secured to each other. A maximum of 4 batteries can be stacked on top of each other in this way. One set consisting of two holders is required per Pylontech battery.

• Properties
• Best possible air circulation
• Connect and secure stacked brackets via clamping device
• Up to four batteries stackable
• Set of two holders for one battery
• Connection set

The Pylontech battery connection cable set includes 2 x 2 meter cables (plus/minus) each with a cross-section of 25mm² and a CAN data cable with RJ45 connectors on both sides. The set is required to connect the Pylontech batteries to an inverter.

• Contents

2m cable plus with M8 ring terminal and Amphenol connector (Pylontech)

2m cable minus with M8 ring terminal and Amphenol connector (Pylontech)